地坪漆供应

环氧地坪漆施工前打磨地面的目的

环氧地坪漆在施工前首先要确认地面情况,环氧地坪在施工中应保持一个洁净的环境,如果地面凹凸不平,有旧油漆,存在疏松层等,就直接影响环氧地坪整体的施工效果,所以要先将地面充分磨平,这样可以减少用漆量,增加附着力,使漆膜不易破坏,并使整体效果看上去更平整、美观。光磊环氧地坪漆厂家针对环氧地坪并对新建水泥地坪上面的水泥块,灰粉起到很好的去除作用,能有效地打开水泥毛孔,以便环氧底漆更好地渗透渗出与吸收,环氧地坪漆工程的质量起到至关重要的作用。

Before construction, epoxy floor paint should first confirm the ground condition. In construction, epoxy floor should maintain a clean environment. If the ground is uneven, there are old paints, and there are loose layers, it will directly affect the overall construction effect of the floor. Therefore, the ground should be fully ground first, so as to reduce the amount of paint used, increase adhesion, make the film not easy to damage, and make the overall effect. It looks smoother and more beautiful. Guanglei Floor Paint Factory aims at epoxy flooring and removes cement blocks and powders on new cement flooring. It can effectively open cement pore, so that epoxy primer can penetrate and absorb better. The quality of epoxy floor paint project plays a vital role. 

所以用专用研磨机对水泥或混凝土地面进行打磨是环氧地坪漆施工工艺中非常重要的一步,以去除其表面的浮浆层,并使基层表面达到要求的粗糙度即可。目的是增强涂层材料与基层的粘结力。具体打磨厚度没有要求,看基层的原先质量。

So it is a very important step in the construction technology of epoxy floor paint to use special grinder to grind the cement or concrete floor, so as to remove the slurry layer on the surface and make the surface of the base meet the required roughness. The purpose is to enhance the bonding force between the coating material and the substrate. Specific grinding thickness is not required, depending on the original quality of the grass-roots.

地面打磨最主要的作用是把地面杂物等清除干净,混凝土毛细孔,有利于环氧地坪漆底漆更容易渗透混凝土地面,粘结得更牢固。而且打磨前地面是亚光而且有灰尘,而做完环氧地坪漆之后,地面很干净,而且返光,原有地面的不平整缺陷显露无疑,所以大家在地坪漆施工前一定要和业主说明白这一点。

The most important function of ground polishing is to clean up the ground debris, concrete capillary holes, which is conducive to the epoxy floor paint primer more easily penetrate the concrete floor and bond more firmly. And the ground before polishing is Matt and dusty, and after finishing the epoxy floor paint, the ground is very clean, and the return light, the original ground irregularity defects are undoubtedly exposed, so we must explain this to the owners before the construction of the floor paint.

地坪漆施工地面打磨的方法有以下三种:

There are three methods of ground polishing for floor paint construction:

干打磨法:用砂纸、乳石、细的石粉进行打磨,然后打扫干净,此法适用于干硬而脆或装饰性要求不太高的地坪漆表面。干打磨的缺点是操作过程中容易产生很多粉尘,影响环境卫生。

Dry polishing method: grinding with sandpaper, milky stone and fine stone powder, and then cleaning. This method is suitable for hard and crisp or decorative floor paint surface. The disadvantage of dry grinding is that it is easy to produce a lot of dust during operation, which affects environmental hygiene.

湿打磨法:用水砂纸蘸水或肥皂水打磨。水磨能减少磨痕,提高涂层的平滑度,并且省砂纸、省力。但水磨后应注意喷涂下层油漆时,一是要等水磨层完全干透后才能涂下层油漆,否则漆层很容易泛白。另吸水性很强的底材也不宜水磨。湿打磨法比干打磨质量好。但是环氧地坪漆施工中都用干打磨法,因为环氧地坪漆施工是装修工程中最后一环,所以工期较短,如果用湿打磨法打磨完,还要等地面彻底干燥,而且如果地面干燥时间不够,环氧地坪漆很有可能会起泡,脱层。

Wet grinding method: grinding with sand paper dipped in water or soapy water. Water milling can reduce wear marks, improve the smoothness of coatings, and save sandpaper and labor. But after water grinding, attention should be paid to spraying the lower layer of paint. First, it is necessary to wait until the water grinding layer is completely dry before applying the lower layer of paint. Otherwise, the paint layer will easily become white. In addition, the substrate with strong water absorption is not suitable for water grinding. Wet grinding is better than dry grinding. But in the construction of epoxy floor paint, dry polishing method is used. Because the construction of epoxy floor paint is the last link in decoration project, the construction period is shorter. If the ground is polished by wet polishing method, the ground will be completely dry. Moreover, if the ground is not dry enough, the epoxy floor paint is likely to foam and delaminate.

机械打磨法:比手工打磨法的生产效率高。一般采用电动打磨机或在抹有磨光膏的电动磨光机上进行操作。打磨时应注意:地坪漆涂层表面完全干燥方可进行;打磨时用力要均匀;湿打磨后须用清水洗净,然后干燥;打磨后不能有肉眼可见的大量露底现象。

Mechanical grinding method: higher production efficiency than manual grinding method. Generally, it is operated by an electric polishing machine or an electric polishing machine with polishing paste. When polishing, attention should be paid to: the surface of floor paint coating is completely dry before it can be carried out; the force should be uniform when polishing; after wet polishing, it must be washed with clean water and then dried; after polishing, there can not be a large number of naked-eye bottom phenomenon.



相关文章